FEATURES:

1. AVR ATMEGA8515 MCU clocked at 8.0MHz
2. Expansion connectors for plug in modules and prototyping area
3. On platform programmer for Atmega 8515 microcontrollers
4. USB interface to PC for programming
5. Every pin is marked in order to make work easier
6. Master Reset/Restart key for hardware reset
7. Input/output & test points provided on platform
8. On platform breadboard
9. Self-contained development platform with on platform DC Power Supply
10. CD with sample project code, Programmer software & useful documents

TECHNICAL SPECIFICATIONS:

• Serial Communication : USB Port
• MCU: ATMEGA8515
• Crystal Frequency : 8Mhz
• Size of Breadboard: 175 x 67 x 8mm
• CPU: CMOS 80C85 4MHz
• Memory: 32Kb Monitor ROM and 32Kb SRAM
• Simple I/O Port: 8-bit GPIO built with 74LS175 D-type F-F and 74LS126 Tri-state buffer
• Programmable Ports: two 8255 chips, system and user ports
• Programmable Counter: 8254
• UART: Classic NS8250 compatible UART
• onboard I/O devices:
• 6-digit seven segment LED,
• 28-keypad,
• 4-bit dot LED indicates status of GPIO,
• buzzer,
• text LCD with CPU bus interface with standard controller HD44780,
• Serial Interface: 9600 RS232C
• +5V Power Supply: Low-dropout voltage regulator with input protection
• 40-pin header for CPU bus
• 40-pin header for user port, 8255 and 8254
• 16-pin header for simple GPIO port
• onboard logic probe power supply
• Test button for single pulse generation to the interrupt pins
• Brownout Protection
• No jumper settings Accessories
• Include a compatible computer.
• Fully printed and hard cover binded instruction manuals in English Warranty:12 months under Suppliers warranty certificate The supplier must attach evidence of the equipment under supply   

Arduino pack
The pack contains:

• 1x Arduino Uno R3 OEM
• 1x 5V Step Motor
• 1x Step Motor Driver Module
• 1x 2x16 LCD Module
• 1x RGB LED Module
• 10x 12x12 Button
• 5x 6x6 Button
• 1x Prototyping Shield
• 1x Water Level Sensor
• 1x Jumper Set 65pcs.
• 1x IR Receiver
• 1x LM35 Sensor
• 1x Flame Sensor
• 1x Mercury Sensor
• 1x LDR
• 1x RC522 RFID module
• 1x RFID Key
• 1x 1x8 Male header
• 1x 5k Potentiometer
• 1x DC Motor
• 1x HC-SR04 Ultrasonic Sensor
• 1x 4 Display
• 2x 2 Display
• 1x 8x8 Dot Matrix LED
• 6x White LED
• 10x Yellow LED
• 10x Green LED
• 10x Red LED
• 1x X-Y Joystick
• 1x RFID White Card
• 1x USB Cable
• 1x Buzzer
• 1x 10k Potentiometer
• 1x MAX7219 IC
• 1x Servo Motor
• 1x Relay Module
• 1x Female Header Set 40pcs
• 1x Male header 40pcs
• 10x Female-Female 20cm Jumper
• 1x Breadboard
• 1x 6 AA Battery w/ DC Jack
• 1x 74HC595 IC
• 1x 4x4 Keypad
• 5x 1K 1/4W Resistor
• 5x 10K 1/4W Resistor
• 8x 220R 1/4W Resistor
• 1x Kutu

Included Accessories

• USB cable, Mains cord, Software SMPS
• 20 Pin FRC cable
• 10 Pin FRC cable
• Patch cords
• Compatible PC.
• Printed instruction manual in English
• A book: Exploring Arduino: Tools and Techniques for Engineering Wizardr ATMEGA 8/16/32/128/168/328P/1280/2560 by using add-on board
• The supplier to attach evidence of the equipment(s) under supply