Set of 5 external turning carbide tool holders with inserts as described below Turning & Facing Tool holder no. 1 Copy Turning Tool Holder (LH, RH, N) nos. 3 (each 1no.) Threading Tool Holder no. 1 Set of 3 Internal boring carbide tool holders with inserts as described below Boring bars nos. 2 Internal threading no. 1 Centre drill dia shank dia 8mm no. 1 Twist Drill dia 6,8,16 & 12mm - 4 (each 1 no.)

1. X axis mm 480
2. y axis mm 360
3. Z axis mm 500
4. Table size mm 600 x 350
5. T- Slot mm 3 x 14 x 100
6. Load on table Kgs 250
7. Spindle Direct Drive, Cartridge Type
8. Spindle nose to table top mm 120 - 620
9. Spindle to Column mm 410
10. Spindle nose taper BT 40
11. Spindle motor capacity Kw
12. Siemens Continuous Rating 
13. 7 Kw / 15 minutes rated output 9Kw
14. Programmable spindle 
15. speed rpm Siemens 10 - 6000
16. Spindle Bearing Front mm Outer Dia: 95mm
17. Inner Dia: 60mm
18. Spindle Bearing Rear mm Outer Dia: 95mm
19. Inner Dia: 60mm
20. Control system SIEMENS 828D Basic SL
21. Progammable feed rate mm/min 0 - 6000 
22. Rapid feed m/min 40
23. Positioning accuracy mm 0.010
24. Repeatability mm ± 0.005
25. Slides Linear motion guide ways
26. Ball screws type 32mm & 10mm C3 Class
27. Axis motor AC SERVO
28. Axis motor capacity Nm 7
29. Main supply 415V±2% 50 Hz and 15A, 3
30. Phase (Customer to specify with order)
31. L x W x H with ATC 
32. (approx.) mm 1900 x 2400 x 2550
33. Weight (approx) Kgs 3000
34. Fully packed L x W x H 
35. without ATC (approx.) mm 1975 x 2475 x 2400
36. Fully packed L x W x H 
37. with ATC (approx.) mm 1975 x 2475 x 2850
38. Weight (approx) Kgs 3300
39. Capacity Ltrs 100
40. Coolant motor Kw 1
41. Lubrication 
42. Automatic lubrication system
43. Compatability / Upgradable FMS / CIM system
44. Tool shank type BT 40
45. No of tool no 20 tools Arm type
46. Actuation type Motorized
47. Maximum tool length mm 250
48. Max tool weight Kgs 6
49. HOLDER RD 16-BT40 COLLET  
50.  NOS CHUCK HOLDER estcert RD 25-BT40 COLLET    
51. NOS CHUCK HOLDER
52. BT40 SHELL END    
53. 1 NO MILL ADAPTOR 16MM
54. B) COLLET
55. RD 16 COLLETS(2mm    1SET to 10mm)
56. RD 25 COLLETS(4mm    1SET to 16mm)
57. TAP Collet RD16(5x4mm, 6x4.9mm or    1SET 6x4.5mm, 8x6.2mm
58. TAP Collet RD25(10x8mm,12x9mm)
59. CUTTER
60. HSS SHELL END MILL SHANK    1 NO DIA.40MM, CUTTER WITH
61. DIA.16MM BORE    notlessDRILL AND TAP
62. TAPE M5,M6,M8,M10,    1 SET
63. TWIST DRILL DIA. 4.2MM, 5MM,    1 SET
64. 6.8MM, 8.5MM,
65. BORING BAR HOLDER AND
66. INSERT
67. BORING BAR DIA.    1 NO 10MM
68. BORING BAR INSERT    1 NO
69. SLOT DRILL, END MILL AND
70. BALL NOSE END MILL 6,8,HSS SLOT DRILL DIA. 1 NO 12MM
71. HSS END MILL DIA.    1 NO 12MM
72. CHAMPER CUTTER    1 NO Ca 45DEG
73. CENTRE DRILL SHANK DIA.    1 NO
74. 8MM TIP dIA 2 MM
75. TOOL CLAMPING    
76. 1 NO FIXTURE
77. 1 set of leveling block.
78. 1 set of machine lighting.
79. 1 set of standard service tool.
80. Complete with 3 axis digital readout system and resolution 0.005 mm.